MG电子抢银行

您好,欢迎来到 东光县腾威焊接设备有限公司Message | Sitemap Hello, welcome to Dongguang Tengwei Welding Equipment Co., Ltd. !

support hotline National Service Hotline: 15632724508

How to perform maintenance on IF welding machine [2019-12-26]
The intermediate frequency welding machine must be properly applied to the grounding device side to ensure full life. Before the application of the intermediate frequency welder, a 500V megohmmeter must be used to test the intermediate ground resistance between the pressurized side of the intermediate frequency welder and the shell. When repairing, you must first disconnect the switching power supply, you can ...
Safety operation steps of intermediate frequency welding machine [2019-12-26]
The intermediate frequency welding machine uses the basic principle of two-point double-point overcurrent electric welding. During the operation of the intermediate frequency welding machine, two electric-level charged steel parts make the double-layer metal material generate a certain contact resistance under the working pressure of the two electric levels. The amount of welding current flows from one level to another ...
Installation and maintenance of intermediate frequency welding machine [2019-12-19]
The intermediate frequency welding machine must be properly applied to the grounding device side to ensure full life. Before the application of the intermediate frequency welder, a 500V megohmmeter must be used to test the intermediate ground resistance between the pressurized side of the intermediate frequency welder and the shell. When repairing, you must first disconnect the switching power supply, you can ...
Safe use of intermediate frequency welding machine [2019-12-19]
The intermediate frequency welding machine uses the basic principle of two-point double-point overcurrent electric welding. During the operation of the intermediate frequency welding machine, two electric-level charged steel parts make the double-layer metal material generate a certain contact resistance under the working pressure of the two electric levels. The amount of welding current flows from one level to another ...
Seam welding machine manufacturers should arrange work reasonably [2019-12-11]
Under the management of the seam welding machine manufacturer's points system, all personal behaviors of employees are matched with points. The higher the score, the higher the employee's ability to work and comprehensive performance. And the staff point status is recorded by the point software, which is managed in the mobile phone software background according to ...
Process management mode of seam welding machine manufacturers [2019-12-11]
Each seam welding machine manufacturer's management system is different, but their common point is standardization. Once the rules and regulations of the seam welding machine manufacturers are formulated, the relevant national standards must be unified. For example, all personnel and rewards and penalties must be strictly observed. The norm is many seams ...
Preparation before use of seam welding machine [2019-12-06]
In the seam welding, electromechanical welding should be done well before welding. The most important thing is to do a good job in each step and each set of inspection work to ensure the power circuit, gas supply, instrument panel, power switch, etc. everything is normal. Below Linyi seam welding ...
What are the advantages of seam welding machines? [2019-12-06]
The application of the seam welding machine is more common, and sometimes the use of this accessory will also cause abnormalities, which will make the production progress. So, what are the key points of the advantages of the seam welder? ...
What to pay attention to when using IF welding machine in winter [2019-11-29]
Intermediate frequency welding machine must be stopped and grounded before being applied to ensure personal safety. The intermediate frequency welding machine must be tested with a 500V megohmmeter before calling. The insulation resistance between the high voltage side of the intermediate frequency welding machine and the casing is not less than 2.5 megohms. Turn off the power first during maintenance, why not ...
What to pay attention to in the use of intermediate frequency welding machine [2019-11-29]
The intermediate frequency welding machine applies the rule of double-sided double-point overcurrent welding. When the intermediate frequency welding machine is working, the two electrode pressurized parts make the two layers of hardware under the side pressure of the two electrodes inevitably touch the resistance of Qin Muchu, and the welding current of the intermediate frequency welding machine When flowing from one electrode to another ...
Analysis of the correct use of welding machine [2019-11-26]
(1) The position of the electro-mechanical level rod for row welding must be adjusted before the electric welding is carried out. The electric level should be just enough to press the weldment. (2) The row welding machine can select the amount of current according to the thickness and material of the weldment to adjust the number of proportional stages of the power switch. ...
Do you know the cleaning method of row welding machine? [2019-11-26]
It is indispensable for the row welding machine to prepare in advance for welding before welding. Dirty things, such as oil stains, often appear in the upper and lower electrical levels. This must be removed by people often. In life, it is a trivial matter ...
MG电子抢银行
MG电子抢银行

Consultation Hotline: 15632724508

Consulting mobile phone: 13393376226

Contact: Manager Wang

Company Address: Nanxiakou Town, Dongguang County, Cangzhou City, Hebei Province

support hotline:
15632724508
online service